Jewelry Kit Instructions and Beading Guides

Add a bicone onto each of your head pins. Wrap each headpin close, and trim off excess wire. Open your large jump ring, adding a leaf, 3 bicones and your necklace. Close jump ring.

Begin by stretching your elastic cord. String a Multi cut silver round, small silver round, cross, crystal round, cross, crystal round, cross, crystal round, small silver round, and multi cut round. After that, alternate small silver rounds,

Unpack your kit Cut 10 inches of cord and set aside Cut remaining cord in half Prep each end of the cord with either glue or lighter pulling it out and making it stiff cut to a point. Wrap head pin as seen below. trim excess wire

Begin by cutting your chain into 2 equal lengths. Run your chain through the hole in your star fish. Open your eye-pin. Being the 2 ends of your chain together and add to the eye pin. Close your eye-pin. Add your bicone,

Cut your chain into 2 equal lengths Take one of your chain pieces. Using a jump ring, attach it to your earring backing. At this point you will need to check the sizing to leave enough chain to dangle under your ear lobe.  Once

Center your clasp on your wire Bring your ends together and add a bicone, crimp tube and bicone. Separate wires, and begin your pattern. Silver round, bicone, gold spacer, bicone, silver spacer, bicone, gold spacer, bicone, silver bead, round

Begin by stretching your elastic.  Add 1 Fancy Jasper gemstone to your cord Begin your pattern.  Silver round, Swarovski briolette, rondel, Swarovski briolette, 3 Jancy jasper gemstones Repeat to your last small silver round. 

On your headpin  load the following Bicone / 4mm squaredell /  flat bead with point up /  8mm squaredell / flat bead pointed down /  4mm squaredell /   flat bead with point up /  8mm squaredell / flat bead with

Being by cutting your wire in half. Center a silver round on your wire. Follow the diagram Making sure to pull both wires up tightly Grab the wires right at the top of your round bead, adjust the wings, and create a loop, wrapping

Step 1) Open your jump rings. Step 2) Connect your star following the image above. Step 3) On the top hole of the top star add a jump ring, and attach your closed ring. Step 4) Attach the ear wire to the closed ring.

Step 1) On your head pin, add the following. Silver round / Top Drill / Top Drill / Squaredell / Top Drill / Top Drill / Squaredell / Top Drill Top Drill / Silver round Step 2) Make sure the head pin is close to what you see in the image above

1) Add your cube to the chain, following our illustration.

Step 1) String a saucer, 6mm bicone, crimp and 4mm bicone. Step 2) Add your clasp, and back through your beads. Pull tightly and crimp. Step 3) Begin stringing your pattern. 6mm cube / saucer / bicone / saucer / 8mm cube / saucer / bicone /

On your small headpin add your pearl and wrap closed. 1) Remove the protective coating from your acrylic frame. 2) On your headpin add a flat bead  , 2 green bicone, tear drop, green round, crystal  rondell,  a red bicone , add

Center 7 pendants on your wire. Double your wire to form your poinsettia, bringing wires up.

1) Stretch your elastic cord. 2) Being your pattern. 3) String a gold bead, football gold bead, and large silver bead. 3) Continue until you have used all your beads. 4) Create your knot and hide it under your large silver bead.

1) Remove protective coating from your snowflakes. 2) Open your jump ring, and connect the snowflake to the bottom of your eye-pin. 3) On your eye-pin add your Half bead, Rondell, and another half bead. 4) Wrap and trim excess wire. 5) Attach

Begin by stringing a crystal round, crimp tube and 4mm bicone onto your wire.    Add your clasp.   Back through your beads.   Pull tightly and crimp.   Begin your pattern.  Rondell, vitrail round, rondel,

1) Remove the protective coating from your acrylic frame. 2) One your headpin add a silver saucer, bell, bicone, bow and bicone. 3) Wrap and trim excess wire. 4) Use a jump ring to attach to the bottom hole of your frame. 5) On your eye-pin

Begin by stretch your elastic cord. String a silver round, lucerna, silver round, and bicone. Repeat this pattern to your last silver round. Add your tassel and large silver pyramid cut bead. Create your knot, and trim excess cord. Hide your

Begin by stretching your elastic. Begin your pattern. Small Silver Round / Cone / Rondell / Cone / Small Silver Round / Crystal Round Repeat to your last small silver round. Add your charm, and large hold silver bead. Create a knot, and trim

Being by stretching your elastic cord. Start your pattern. 2 Gemstones, crystal round, squaredell, crystal round, 3 gemstones, crystal round, squaredell, crystal round Continue to your last gemstone. Add your large hole